Safety Specifications for Driving and Operating Electric Pallet Trucks Operation Safety of Electric Pallet Trucks -

The electric pallet truck is safe to operate and operate safely.

The electric pallet truck is powered by battery to drive the travel motor and hydraulic system motor to realize travel and loading and unloading operations. Compared with internal combustion pallet trucks, electric pallet trucks have the advantages of no pollution, convenient operation, energy saving and high efficiency. Next, let's take a look at the safe operation rules of electric pallet trucks.

Safety operating procedures for electric pallet trucks.

Installation and debugging of electric pallet truck Before starting the electric pallet truck, it is necessary to check whether all parts are in good condition, and the performance of all operating parts and safety devices. The mobile pallet truck can only use the current generated by the battery, not the rectified alternating current, so as not to damage the electronic components.

Before moving the pallet jack, the brakes and battery must be checked for full charge. Open the electric lock, move the control rudder to its motion position, slowly turn the accelerator, and move to the corresponding working area. Turn the accelerator forward to make the pallet truck move forward, turn the accelerator backward to back up, and make the accelerator return to the neutral position to stop. Starting, stopping, or changing movements should be slow, as sudden movements can be dangerous (especially when walking at high speeds).

When the pallet truck is walking, the load should be in a low position, the height of the fork from the ground should not exceed 300 mm, and the speed should be reduced in narrow passages or corners. Stacking operation of electric pallet jacks.

1) The load is low, be careful close to the shelf (the platform must be erected, and the driver should stand on the ground to operate).

2) Make sure the front legs of the pallet jack can move freely under the pallet or shelf.

3) Raise the load until it rises above the shelf.

4. Slowly move the electric pallet truck forward, stop when the load is above the shelf, and release the fork out of the pallet to ensure the safe placement of the load, and do not apply additional pressure to the lower shelf when unloading. force.

5. Step back slowly to make sure the tray rests smoothly on the shelf.

6) Reduce the fork back to the moving position.

The electric pallet truck unloading operation.

Place the fork at the bottom of the fork, orthogonal to the shelf.

2) The fork is withdrawn from the bottom of the shelf.

3) Raise the fork to the required height, make sure that the fork can easily enter the pallet, and slowly approach the unloading pallet until the load is safely placed on the fork.

4) the forks until the pallet lifts off the shelf.

5) Slowly back the channel.

6) Slowly reduce the load while ensuring that the fork does not encounter obstacles when falling.

Electric pallet truck battery charging operation.

The inspection, charging and replacement of the battery must be carried out by professionals in accordance with the instructions. The charging site must be well ventilated, and no smoking or flammable, spark-prone substances are allowed near the electric pallet truck or the charger. The weight and size of the battery will affect the stability of the pallet truck, so if you want to install a non-standard battery, it is wise to link with the production height and obtain relevant certification.

Check the temperature of the battery before charging. Below 30°C, the electrolyte level is not lower than the separator (if below the separator, add distilled water to the baffle), and then check the performance of the wire . Place the charging socket (A) and the charger charging plug (B) on the charging plug, so that the shape of the charging device is turned on. During the charging process, the temperature of the battery cannot exceed 45°C. If it exceeds, stop charging, let the battery cool down, and recharge with a lower current. After charging is completed, the charging current of the charger is disconnected, and STOP lights up. At this time, the switch is turned off, and the battery socket in the charging plug (B) can be unplugged (A).

The electrolyte density of each single battery should be between 1.27~1.29kg/1.25℃, and the normal charging time of each battery can be maintained for 14~16 hours. The liquid density is about 2.7V. Recharge the battery every working day.

Note: The battery must not be discharged! Avoid partial charging and allow the charger to signal when charging is complete. Battery replacement operations for electric pallet jacks.

Remove the battery retaining screws.

Remove the cable from the battery terminals.

3) Pull out or hang the battery.

4) Install the battery according to the above reverse process, tighten and connect correctly.

(The replacement battery must be of the same model)

Notes.

1) Charge in a well-ventilated area, open the top cover or remove the battery from the pallet jack.

2) Batteries should not be exposed to open flames. Explosive gases may cause fires.

3) Do not make temporary connection or wrong connection.

4) The ends should be open and not peeled off, and the cable insulation must be reliable.

5) Keep the battery clean and dry, and use an antistatic cloth to remove dust.

6) Do not place tools or other metal objects on the battery.

7) The temperature of the electrolyte should not exceed 45°C during charging.

8) After charging, check the electrolyte level, which should be 15mm higher than the separator. Under normal circumstances, refill with distilled water once a week.

9) Avoid contact with the skin and acid, once in contact with a lot of soapy water or consult a doctor.

10) Used batteries should be disposed of according to local regulations. Repair and maintenance of electric pallet trucks The maintenance of electric pallet trucks must be carried out by professionals, and a comprehensive inspection should be done at least once a year. After each maintenance operation, the performance of the pallet truck and its safety devices should be checked. Check pallet jacks regularly to avoid risk of downtime or injury.

.

The , essentially perfected by pedestrian pallet stacker, is one of the first home appliance to be widely distributed.
It is clear that is one of the best methods that can be used for the purposes of portable pallet jack. If you want an and other electric stacker, you should find the right provider who will guide you through and offer something that will help your business. For quality , go to Staxx Pallet Truck.
There's the area of manufacturing pallet stacker truck that's becoming very important. If you can create those things, you build this closed bond.