Introduce you to the method of measuring the working performance of the forklift

are industrial vehicles used for loading and unloading goods, and can also be used for short-distance transportation of large objects. Use fuel or batteries. The electric lithium pallet truck manufacturer introduced that the structural characteristics and working performance of the forklift are measured by its technical parameters. In addition to the familiar rated lifting weight and lifting height, there are many technical parameters of the lithium pallet truck. The following is a detailed introduction to the technical parameters of the forklift.

1. Rated lifting capacity: The rated lifting capacity of a forklift refers to the weight of the goods that can be lifted when the distance from the center of gravity of the goods to the front wall of the fork is not greater than the distance between the load centers, expressed in T (tons) . When the center of gravity of the goods on the fork exceeds the specified load center distance, the lifting capacity should be reduced accordingly due to the limitation of the longitudinal stability of the forklift.

2. Load center distance: Load center distance refers to the horizontal distance T from the center of gravity to the front wall of the vertical section of the fork when a standard cargo is placed on the fork, expressed in mm (millimeters). For 1T to 4T forklifts, the specified load center distance is 500mm.

3. Lifting height: Lifting height refers to the vertical distance between the upper surface of the horizontal section of the fork and the horizontal ground where the forklift is located when the forklift is fully loaded and the goods are raised to the position on a flat and solid ground. .

4. The inclination of the gantry: the inclination of the gantry refers to the inclination of the gantry forward or backward relative to its vertical position when the unloaded forklift is on a flat and solid ground. The function of the forward inclination angle is to facilitate fork picking and unloading of goods; the function of the rear inclination angle is to prevent the goods from slipping off the fork when the forklift is running with goods. Generally, the forward inclination angle of the forklift is 3°~6°, and the rear inclination angle is 10°~12°.

5. Lifting speed: The lifting speed of the forklift usually refers to the speed at which the goods are lifted when the forklift is fully loaded, expressed in m/min (meters per minute). Increasing the lifting speed can improve the work efficiency, but the lifting speed is too fast, which is prone to cargo damage and machine damage accidents. The lifting speed of domestic pallet stacker has been increased to 20m/min.

6. Driving speed: Increasing the driving speed has a great influence on improving the working efficiency of the forklift. For an internal combustion forklift with a lifting capacity of 1T, the travel speed when fully loaded is not less than 17m/min.

7. Smaller turning radius: When the forklift is running at low speed with no load and turning with full steering wheel, the smaller distances from the outer and inner sides of the vehicle body to the turning center are called smaller outer turns respectively. Outside the radius Rmin and within the smaller inside turning radius rmin. The smaller the outer turning radius, the smaller the ground area required for the forklift to turn, and the better the maneuverability.

8. Small ground clearance: Small ground clearance refers to the distance from the fixed point on the vehicle body to the ground other than the wheels, which indicates the ability of the forklift to cross the raised obstacles on the ground without collision . The smaller the ground clearance, the higher the passability of the forklift.

9. Wheelbase and Wheelbase: The wheelbase of a forklift refers to the horizontal distance between the centerlines of the front and rear axles of the forklift. Wheelbase refers to the distance between the centers of the left and right wheels on the same axle. Increasing the wheelbase is beneficial to the longitudinal stability of the forklift, but it increases the length of the body and increases the smaller turning radius. Increasing the wheel base is beneficial to the lateral stability of the forklift, but it will increase the overall width of the body and the smaller turning radius.

10. Smaller width of right-angle aisle: The smaller width of right-angle aisle refers to the smaller width of the aisle intersecting at right angles for forklifts to travel back and forth. Expressed in mm. Generally, the smaller the width of the right-angle channel, the better the performance.

11. Smaller width of stacking aisle: The smaller width of stacking aisle is the smaller width of the aisle when the forklift is in normal operation.

It can be seen that the technical parameters of the forklift are quite a lot. When purchasing a forklift, you should observe it carefully and choose a forklift with excellent performance. manufacturers also remind everyone that although increasing the lifting speed can greatly improve the efficiency, if the lifting speed is too fast, it is very prone to accidents. The small outer turning radius is small, the ground clearance is small, and the width of the right-angle passage is small. The forklift has excellent performance.

Ningbo Staxx Material Handling Equipment Co.,Ltd. thinks that customer satisfaction is one of the most important determinants of brand loyalty. High-quality service can be the difference between a one-time buyer and a lifelong repeat customer.
Ningbo Staxx Material Handling Equipment Co.,Ltd. will accomplish this by exceeding the expectations of our customers while conserving resources and preserving the quality of the environment.
pallet stacker truck, is an alternative product for staxx pallet truck to investors and consumers who are passionate about our products or services.
While hand pallet jack, battery operated pallet stacker pallet stacker truck can help achieve high accuracy._x000D_
pallet stacker truck can be great additions to companies looking to improve the well-being of their employees, as well as increase the efficiency and productivity of their workers across the organization.