The most detailed explanation of the parameter names of electric stackers and pallet trucks is worth collecting!

Rated load: The rated load of electric stackers and electric pallet trucks refers to the maximum weight of goods that are allowed to be lifted when the distance from the center of gravity of the goods to the front wall of the fork is not greater than the distance between the load centers, expressed in t (tons) . When the center of gravity of the cargo on the fork exceeds the specified load center distance, due to the limitation of the longitudinal stability of the electric stacker and electric pallet truck, the lifting weight should be reduced accordingly. Load center distance: The load center distance refers to the horizontal distance from the center of gravity to the front wall of the vertical section of the fork when a standard cargo is placed on the fork, expressed in mm (millimeters). For the 1t electric stacker and electric pallet truck, the load center distance is 500mm. Maximum lifting height: The maximum lifting height refers to the vertical distance between the upper surface of the horizontal section of the fork and the ground when the electric stacker or electric pallet is fully loaded, and the goods are lifted to the highest position. Mast inclination angle: The mast inclination angle refers to the maximum inclination angle of the mast forward or backward relative to the vertical position of the unloaded electric stacker on a flat and solid ground. The forward inclination angle is to facilitate fork picking and unloading of the goods; the backward inclination angle is to prevent the goods from slipping off the forks when the all-electric stacker or semi-electric stacker is running with the cargo. Maximum lifting speed: The maximum lifting speed of all-electric stackers and semi-electric stackers usually refers to the maximum lifting speed of goods when the lithium pallet truck is fully loaded, expressed in ·m/min (m/min). Increasing the maximum lifting speed can improve operation efficiency; however, if the lifting speed exceeds the limit, cargo damage and machine damage accidents are prone to occur. At present, the maximum lifting speed of domestic forklifts has been increased to 20m/min. Maximum travel speed: Increasing the travel speed has a great impact on improving the operating efficiency of the forklift. For an internal combustion forklift with a lifting capacity of 1t, its maximum travel speed when fully loaded is not less than 17m/min. Minimum turning radius: When the electric stacker or electric pallet truck is driving at a low speed without load and turning with a full steering wheel, the minimum distance from the outermost and innermost sides of the vehicle body to the turning center is called the minimum outer turning radius Rmin and Within the minimum inside turning radius rmin. ·The smaller the minimum outside turning radius, the smaller the ground area required for the forklift to turn and the better the maneuverability. Minimum ground clearance: The minimum ground clearance refers to the distance from the lowest point fixed on the car body to the ground outside of the wheels. It represents the ability of the electric stacker and electric pallet truck to cross over the raised obstacles on the ground without collision. The greater the minimum ground clearance, the higher the passability of the forklift. Wheelbase and wheelbase: The wheelbase of electric stackers and electric pallets refers to the horizontal distance between the centerline of the front and rear axles of the forklift. Wheelbase refers to the distance between the center of the left and right wheels on the same axis. Increasing the wheelbase is conducive to the longitudinal stability of the forklift, but it increases the body length and the minimum turning radius. Increasing the wheelbase is beneficial to the lateral stability of the forklift, but it will increase the overall width of the vehicle body and the minimum turning radius. The minimum width of the right-angle channel: The minimum width of the right-angle channel refers to the minimum width of the channel that intersects at right angles for the power-powered stacker trucks and electric pallet trucks to travel back and forth. Expressed in mm. Generally, the smaller the minimum width of the right-angle channel, the better the performance. Minimum width of stacking aisle: The minimum width of stacking aisle is the minimum width of the aisle when the electric stacker and electric pallet truck are in normal operation.
Ningbo Staxx Material Handling Equipment Co.,Ltd. is specialized in sourcing staxx pallet truck pallet stacker truck through its unparalleled worldwide network of supply. Go to Staxx Pallet Stackers, you will surely find your ideal at the most favorable price.
Ningbo Staxx Material Handling Equipment Co.,Ltd. aims to hire several additional experienced marketing professionals that can add to our existing talent-pool and help continue the steady growth of our business.
The risk of hydraulic hand pallet truck is reduced by pedestrian pallet stacker with the consumption of .